Morini
Advanced Member
Last Activity: Today, 02:00 AM
Joined: 12-21-2017
Location:
-
Also, can anyone who suffered from ISS pipe in. It is absolutely a factor. Ron from gunghogolf did a nice write up about it, becomes it comes up so much:... -
A couple of quick things to try:- Tee up an iron. The fiberbuilt is a good mat in terms or getting good spin and keeping launch low. But if you are not
Leave a comment:
-
- The dot doesn't do anything other than act as a rough guide of where to place the ball. It is not connected in any way to actually reading the ball.
Last edited by Morini; Yesterday, 10:41 PM.Leave a comment:
-
It is not realistic because it uses ball speed and divides by an assumed smash (PTI). Skytrak tries to be clever, and the low spin in your shots causes...Last edited by Morini; 05-26-2020, 04:28 PM.Leave a comment:
-
I know that. Don't know what else to tell you. Something very bad is happening in second set as spin is about 30% of what it should be. Your swing speed...Leave a comment:
-
I have played around with course design, but recently decided to stick it out and actually re-create a course from lidar. However, I run into this issue....Leave a comment:
-
That is correct. However, E6 still hasn't integrated the latest image engine. At least not as far as I know. In other words, the update hasn't trickled... -
One other thing. The ball speed is right at the edge of the speed where the Skytrak high ball speed fix will make a difference. The fix was included in...Leave a comment:
-
I put Uneekoor data from the shot at 5:20 into flightscope optimizer. 750 feet of elevation and got 245 yards carry, pretty well in line with the other...Last edited by Morini; 05-25-2020, 03:20 AM.Leave a comment:
-
I believe offset to be one of the causes of what many users think is "left bias". If hitting onto a screen, the center line should be moved...Leave a comment:
-
Oh, and Gresh12, you mean that the ball flight model overreads spin, right? Not the measured spin axis. There is a poster in one of the facebook groups... -
Yes, it is a known weakness. Skytraks official tolerance is +- 2 degrees. It is not clear if this is average error, standard deviation, 95% confidence...Last edited by Morini; 05-22-2020, 10:27 PM. -
Also, there quite a few users reporting brutal HLA when in FMJ. I would guess that putts are at the very bottom of the field of view, and lots of issues... -
Fair enough, but it holds more so for your full swing comparisons. Skytrak is finicky, and thousands have learned this is the way to do it. Yes, it would... -
It sounds as if you assume the proper way to align Skytrak is to be super super exact on having it parallel to the target line. Just to clarify that is...Last edited by Morini; 05-22-2020, 07:51 PM.Leave a comment:
-
Don't forget the link.Leave a comment:
-
Very strange. Does E6 report ball data? If so, compare them to ST range to see which metrics are off. Somebody else had similar issue maybe 3 months ago....Leave a comment:
-
Sorry I thought you were talking about the club head data that was included in an earlier version. of skytrak software.
The easiest thing...Last edited by Morini; 05-22-2020, 04:58 PM.Leave a comment:
-
Foot spray club face. If center contact, these numbers are close. If not, disregard. There is simply no way knowing whether spin axis comes from path/face...Leave a comment:
-
E6 gets sent the ball data from Skytrak. It then uses the Skytrak ball flight model to render ball flight. Finally, as the ball intersects the ground,...Leave a comment:
No activity results to display
Leave a comment: