Tweet
As I posted awhile back the flash module is really easy to disassemble with a heat gun and a utility knife.
I finally got around to replacing the xenon flash tube which was broken and is most likely the cause of most all flash module failures. The old flash tube and reflector assembly is easily unsoldered from the circuit board using a small fine tip solder iron.
The replacement xenon tube a XFTR-1015-2300 Reflector with Flashtube Item# XFTR-1015-2300, from Xenonflshtubes.com seems to be an exact replacement for the factory tube assembly. They cost 5.95 USD in quantities of one. The company is in Israel so there is a shipping charge. To the US it took about 10 days and the total cost for three tubes and shipping was 26.85.
I installed the repaired module in the GC2 and it seems to work perfectly. It picked up all shots from drives to putts correctly. This was not an extensive test since the hitting cage is in my garage where it is uncomfortably hot this time of year. When the weather cools off a bit I'll reinstall it and see how long it lasts.
Given the alternative of buying a new flash module for 150-500 dollars this seems to be an easy and inexpensive fix. Once you initially get the original failed module apart it takes about 5 minutes to make the switch. Once taken apart you can just snap the module casing back together with no need to reglue since the attachment screws will hold the assembly together.. That way you can just take it out of the GC2 unsnap it and replace the xenon tube rapidly.
In summary you will need a small low powered soldering iron with a fine tip, a wire stripper, as the wires attached to the replacement xenon tube assembly are rather long, rosin core solder, some rosin remover (I use carburetor cleaner). and some kind of easily removable adhesive (I used a dab of some 5 minute epoxy) to hold the flash tube reflector solidly in the circuit board. Unless this replacement tube lifespan is so short you have to replace it very often there would not seem to be any reason to not just repair one that bursts the flash tube and therefore quits working.
I don't plan in spending any time looking for a more robust bulb since this one is so easy to replace and comes as a sub assembly with wires and a reflector.
I finally got around to replacing the xenon flash tube which was broken and is most likely the cause of most all flash module failures. The old flash tube and reflector assembly is easily unsoldered from the circuit board using a small fine tip solder iron.
The replacement xenon tube a XFTR-1015-2300 Reflector with Flashtube Item# XFTR-1015-2300, from Xenonflshtubes.com seems to be an exact replacement for the factory tube assembly. They cost 5.95 USD in quantities of one. The company is in Israel so there is a shipping charge. To the US it took about 10 days and the total cost for three tubes and shipping was 26.85.
I installed the repaired module in the GC2 and it seems to work perfectly. It picked up all shots from drives to putts correctly. This was not an extensive test since the hitting cage is in my garage where it is uncomfortably hot this time of year. When the weather cools off a bit I'll reinstall it and see how long it lasts.
Given the alternative of buying a new flash module for 150-500 dollars this seems to be an easy and inexpensive fix. Once you initially get the original failed module apart it takes about 5 minutes to make the switch. Once taken apart you can just snap the module casing back together with no need to reglue since the attachment screws will hold the assembly together.. That way you can just take it out of the GC2 unsnap it and replace the xenon tube rapidly.
In summary you will need a small low powered soldering iron with a fine tip, a wire stripper, as the wires attached to the replacement xenon tube assembly are rather long, rosin core solder, some rosin remover (I use carburetor cleaner). and some kind of easily removable adhesive (I used a dab of some 5 minute epoxy) to hold the flash tube reflector solidly in the circuit board. Unless this replacement tube lifespan is so short you have to replace it very often there would not seem to be any reason to not just repair one that bursts the flash tube and therefore quits working.
I don't plan in spending any time looking for a more robust bulb since this one is so easy to replace and comes as a sub assembly with wires and a reflector.
Comment