General Questions / Answers

[Willymakit]

I did change my lighting to different positions about two weeks ago. At the beginning it was working better then the way I had it the first time. Might have to change it back or position lightening a little different. At least it's something to work on

[JohnMeyer]

I'm not really sure how it works but my understanding of how the unit works was that it outputs a beam of (red ir led) and receives a reflection from the club back into the unit (black IR LED) which give the clubs position and angles at various points throughout the swing.

If this is the case then in theory no external light at all should be fine, in fact should improve things id have thought (other than the fact its harder for you to see the ball lol,) but as far as optishot is concerned id have thought the best possible scenario would be no external light sources interfering with the IR receivers. I guess thats why they recommend CFL lighting as minimal IR.

Again also thought this as taping clubs (making them more reflective) made the system work better.

That was my thinking behind the lighting suggestion anyway.

[Willymakit]

I did send optishot a email about a month ago and told them what I had for a setup. And they said I didn't have enough light. That's why I put the lamp directly over the sensors. but I don't think that helped.

thabks for the input. Will try using those options.


I even using the offset at different settings and was still getting roughly the same numbers for open and closed club face.

[Willymakit]

As vega says try the sensor test and that shoukd show up any problems

Also try removing ya turf from unit and again do the sensor test.

If your using a projector and screen when it's dark outside turn off all lights sort from projector and try the sensor test again

That way should be able to narrow it down to turf, lighting or sensor itself

How old is your unit?

I bought it in sept of 2013. I used it a few times in spring of 2014 but since this online started up I been using it a lot more.

[Willymakit]

Before I downloaded optishot 2 I really didn't have these problems like I do now. i think I have always had the problems but msybe not to this degree. But since playing in tournsments and watching other guys play I have noticed the degree of the club wasn't off has much has my were. Before my driver was really bad. Was getting 15 degree closed or open but that was because of not using tape. But the driver is much more consistent But I noticed my irons are way off. I will take a half a swing with straight wrist so the club can not turn or twist and it will still read 10 degree open or closed.

I think the only reason why I score well sometimes is the fact I can get close enough with the drive to the green so I can use my 52 degree and even with the club face open or closed 10 degree I manage to get it close enough to make birdie.

[Vincent_Vega]

Yeah. The senor diagnostics is completely separate from the software where you play the game, you won't find it in there. I found it in the start menu under Optishot when I had to use it. As they also suggested, you may want to try just the dark room with only the light from the projector. I can't access twitch at work so I'm not able to see your setup right now. The concern is, that you weren't having these problems until recently.

[JohnMeyer]

As vega says try the sensor test and that shoukd show up any problems

Also try removing ya turf from unit and again do the sensor test.

If your using a projector and screen when it's dark outside turn off all lights sort from projector and try the sensor test again

That way should be able to narrow it down to turf, lighting or sensor itself

How old is your unit?

[Willymakit]

It sounds like your unit may be faulty Jason. The only other thing I know to try is the sensor diagnostics. I'm not sure if that's exactly what it's called but you can find it under the start menu. It basically just test to see if all the sensors are reading properly. You run a club across it kind of like you do when you calibrate.

I will have to look for this option. Didn't know anything about it. I have a optishot 1 but downloaded optishot 2

I did stream match last night and about 4 or 5 holes in I turned on camera. I had it facing the screen so hopefully my setup was showing.

[wbond]

I would suggest trying it without the directly over the sensors. Maybe move it up and away but on the sensor side. Do not have any lighting coming from behind you casting shadows of yourself onto the sensor. Do you have pictures of your setup, if so, please post and maybe some people can give you suggestions to optimize your lighting. That is the problem i have found with this system, it is very picky about lighting and shadows. FWIW, I've found that the p3 is not nearly this problematic. I have both and a skytrak.

So I'm to the point of frustration of throwing this optishot out if the reading I get with irons and sometimes the driver is off the charts. I'm getting readings of 10 degrees open or close I even manipulate the club and still get the same results.

Here is my setup. Have a lamp directly over the sensors roughly 8-10 inches above with enough clearance to swing club and not hit the lamp. Have a bulb that is forescent light. Have taped my clubs and and calibrated and re calibrated and even deleted the calibration and I'm still getting readings of 5-10 open or closed on almost every shot. I have unplugged the optishot and still get the same results. If I can't figure this out I might just quit playing.

Any other suggestions. I was so upset last night after playing john that I stayed up for another 2 hours trying to figure something out and still getting the same results. Even changed irons and still same results. I don't think I got any sleep last night because of thinking of trying different things.

I emailed optishot this morning. Hopefully they have some suggestions I can try. Or I could just have a faulty optishot.

[Vincent_Vega]

So I'm to the point of frustration of throwing this optishot out if the reading I get with irons and sometimes the driver is off the charts. I'm getting readings of 10 degrees open or close I even manipulate the club and still get the same results.

Here is my setup. Have a lamp directly over the sensors roughly 8-10 inches above with enough clearance to swing club and not hit the lamp. Have a bulb that is forescent light. Have taped my clubs and and calibrated and re calibrated and even deleted the calibration and I'm still getting readings of 5-10 open or closed on almost every shot. I have unplugged the optishot and still get the same results. If I can't figure this out I might just quit playing.

Any other suggestions. I was so upset last night after playing john that I stayed up for another 2 hours trying to figure something out and still getting the same results. Even changed irons and still same results. I don't think I got any sleep last night because of thinking of trying different things.

I emailed optishot this morning. Hopefully they have some suggestions I can try. Or I could just have a faulty optishot.

It sounds like your unit may be faulty Jason. The only other thing I know to try is the sensor diagnostics. I'm not sure if that's exactly what it's called but you can find it under the start menu. It basically just test to see if all the sensors are reading properly. You run a club across it kind of like you do when you calibrate.

[Willymakit]

So I'm to the point of frustration of throwing this optishot out if the reading I get with irons and sometimes the driver is off the charts. I'm getting readings of 10 degrees open or close I even manipulate the club and still get the same results.

Here is my setup. Have a lamp directly over the sensors roughly 8-10 inches above with enough clearance to swing club and not hit the lamp. Have a bulb that is forescent light. Have taped my clubs and and calibrated and re calibrated and even deleted the calibration and I'm still getting readings of 5-10 open or closed on almost every shot. I have unplugged the optishot and still get the same results. If I can't figure this out I might just quit playing.

Any other suggestions. I was so upset last night after playing john that I stayed up for another 2 hours trying to figure something out and still getting the same results. Even changed irons and still same results. I don't think I got any sleep last night because of thinking of trying different things.

I emailed optishot this morning. Hopefully they have some suggestions I can try. Or I could just have a faulty optishot.

[Buckeye]

I have a pretty steep swing as well. I usually only get 9 holes or so out of a ball in real life before I replace it.

[sliceomatic]

Do you tend to hit down hard onto the ball? I noticed some nicks in my almost golf balls but I have a pretty vertical swing.

[Buckeye]

Not really related to why a golf ball would crack, but when I was researching impact screens I came across a couple different forums that claimed if you use a damaged ball it increases the likelihood of your screen failing. The idea was that cuts, nicks or dings could cut the screen on impact, so I have been trying to use new or near new balls. Thankfully I have a pretty good connection at a private club that uses prov1's as range balls, so I can get them fairly cheap.

[Willymakit]

I'm golfing in my heated basement. If anything it's warmer then in summer time.

Even summer time it's usually once a week with real ball. When I first got the optishot I used a prov1. Lasted 3 days.