Announcement

**Cklguy2013** · 02-11-2016, 07:47 PM

Thanks for posting.

**Cklguy2013** · 02-12-2016, 07:46 PM

Has this update messed up the setting files?

I'm not getting proper launch angles on my wedges now,
- about 50 % of the time they seem to max out at a certain loft, 23 degrees on a SW and 31 degrees on a LW
I'm getting random very high launch drivers,
- 34 degree launch angle, about 1 in 3
Only about 1 n 3 drivers is ready,

Btw, launch angles appear to read correctly in the preview screen.

Other than that all good though.... grrrrrrrr.......

**Cklguy2013** · 02-12-2016, 10:03 PM

Yes I have PT1 for and Pt5... would they have changed with the update??

**Cklguy2013** · 02-13-2016, 05:12 PM

Switched Vcam to Pt1 but to no avail still better with pt5, funny with driver still seems to be old waggle issue, and with short wedges get the odd misread on launch.... puzzling.....

**Cklguy2013** · 02-13-2016, 06:52 PM

So after some further testing the driver seems to work if I don't waggle, and the LA seems pretty good with the driver, curiously though with the other clubs they can seem to get locked into a LA, say my 7 iron for example which I usually launch at 20 degrees, gets locked into a 30 degree LA, and on other occasions short wedges (i.e. 35 yards), which I might launch at 35 degrees, show 23 degrees, so very inconsistent launch conditions overall, sometimes too high, sometimes too low. Also, balls seem to launch very low out of the heavy rough. So all in all the system is all over the place on LA, which wasn't a problem before I did this update. Protee Help!!

**ProTee United** · 02-15-2016, 09:52 AM

The waggle problem can be fixed. Open the advanced settings editor in the interface with ALT-E. Find the value Max_swing_tempo and make sure its set to 99.
Close, save and restart the interface.

Shots not being detected and camera not picking up shots might be related to the light setup. Make sure your overhead lights are aligned. Also worth a try replacing the bulbs. They only last an x amount of hours. Then contact the help desk if you still experience problems.

**Cklguy2013** · 02-15-2016, 02:26 PM

Thanks I switched all the Vcams to PT1 other then the wedge which I left at PT4 and they seem to be working now. Also, why are there 2 wedge PT settings? One with the group of other PT settings and one further below? Oddly, previously I had the first set to PT5 and the second to PT4.

P.s. Lights are fine, as streaks show well, so wasn't that.

**Cklguy2013** · 02-15-2016, 08:28 PM

Max_swing_tempo=99 was set to 99 already, and still have waggle problem. Everything else working well now with new PT settings.

**Boerdoc** · 02-16-2016, 02:56 PM

I just updated the interface from 3.07e to 3.07f. This changed many of the settings from what I had set before. Club path and club face settings as well as "make club face straight" and use pitching speed, etc. I suggest you check what changed from your previous settings. Even the gear effect was changed from on to off.

Also, in the previous version there was not 2 PTs for wedges. this is new. One is for hcam and one is for vcam. The second one is not adjustable or changeable from outside "Alt-e" and it is in an area that says do not change, use the interface to make changes.

BTW, I have not played since I made the update. And my Hcam is still grey, vcam is red.

**Cklguy2013** · 02-16-2016, 03:48 PM

Hey Protee, can you comment on boerdec's comments above, I'm curious as to whether the path and face numbers might have been adjusted as well?? Before the update, I pretty much always had a closed club face with my iron, say 2 to 4 degrees, now I'm getting an open club face of about 2 degrees, which may be correct, but I'll have to admit I'm wondering if my swing has changed or if the numbers in the interface were altered in some fashion.

**ProTee United** · 02-16-2016, 04:03 PM

Nothing changed. The only thing added was the ability to select a different detection method for the HCam - wedges. Apparently this ended up in the wrong section, but it works.

Just in case we installed a clean 3.07e and saved the settings to an external file, then updated to 3.07f and compared the settings. All the same expect for the version number and HCam for wedges addition.

You can very easy downgrade to an earlier version.

**Boerdoc** · 02-16-2016, 05:49 PM

Maybe I should clarify what I mean about the numbers changing. Some players have needed to change the original settings in the interface to accommodate for their specific setups in protee. For example, I may have needed to change the driver club face angle from say 0 to -2, just making up numbers here. I had that in my interface settings and all was going well. When I updated to 3.07f, this number changed to something else. So "MY" custom settings were changed. What is weird is that not all of the custom ones changed. Moreover, some that changed did not change to the "default" setting. Sooo, What I am trying to say, a bit long-winded, is that after an update, i check what has changed from my custom settings and adjust accordingly.
Protee's last comments about the fresh install of 3.07e updating to 3.07f makes sense. These settings have not been customized. BUT

My questions for Protee are.

1. What is the proper way to update that will keep the old "custom" settings? (is that possible?)

2. Why do the default settings not get set when doing an update? I wish I had a good example but I am not at home. An example would be that the default is "false" and the update makes it "true". In other words, when performing a new install, shouldn't the default settings be installed. Make default, the default.

FWIW, I know that I personally had a few challenges in the beginning that were solved by protee and help from Bubba. Perhaps an uninstall of the interface through an uninstaller program that removes all traces of the interface and a fresh install would help rather that updating what I have with any windows registry gremlins lurking about.

**Cklguy2013** · 02-16-2016, 08:16 PM

Hey Protee,

There is definitely a problem with this update. I tested square club strikes using a laser center line and found the following results for the different iron club face corrections:

-10 - open 6 degrees
-5 - open 4 degrees
0 - open 2 degrees
1 - open 1 degree
5 - open 3 degrees
10 - open 6 degrees

In other words no way to close the club face via the corrections.

**ProTee United** · 02-16-2016, 08:54 PM

Our updates NEVER overwrite your settings file. You have to remove it manually in order for the update to install a new one.

The update might add a new variable. It does not change or remove anything.

My advise is to simply downgrade to the release you were running before the update and then let me know if all works normal again.

Announcement

ProTee Interface 3.07f released

ProTee Interface 3.07f released

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment