Some how I got it to work once. I had input and output both connected. But when I restarted my computer, I can't get it to work again. Keep getting INPUT disconnected. I triple check all the settings, can't figure out why.
-
-
It's a Bluetooth issue. Try hitting a shot to get the GC2 running when not connected then connect again. It's that or your Bluetooth is too far. It needs to be really close with an extension. If it's far it'll also be slower.My Courses:
World Par 3's by mthunt
Toronto GC (L) mthunt
Burlington G&CC by mthunt
Weston G&CC by mthunt
London Hunt Club L mthunt
Park CC Lidar mthunt
Sunningdale GC Robinson L
Sunningdale GC Thompson L
Muirfield Village (liDAR) First Ever Lidar course
Country Club of Castle Pines (liDAR)
The Sanctuary GC ProTee L
The National GC L mthunt
Mississaugua GC L mthunt
Shaughnessy G&CC L mthunt
Markland Woods CC mthunt
Hidden Lake Old L mthunt
Magna GC L mthunt
Barrie CC L mthunt
mthunt RangeComment
-
go to your settings panel and check Bluetooth connections. the GC2 needs to say 'connected', not just paired. If you can't get it to connect, delete and re-pair. I have no idea why, but I wind up needing to do this every once in a while. Perhaps the connection get corrupted. In any case, it is a PIA, but it should work.Comment
-
This golf sim lark is going to be the end of me.....
please help!
Im stuck on:
5: Start up the ProTee Interface. Click on Settings. Set Use External Data to ON. Then Save, Close, Exit, and then restart the Interface.
because when I click the slider to change "external data" to ON, I get a pop up window that's says:
"This change takes effect only after saving the settings and restarting this Protee Golf Interface"
In this window, my only option is to click continue, and once clicked, the slider remains greyed out to "off" no matter what I do.
also, someone mentioned that the GC2 needed to be showing as connected rather than paired in the Bluetooth settings, but my GC2 just stays at paired.
someone please help me I'm dying out here!Comment
-
I have windows 10. When my GC2 is off, it will say "Paired" in the bluetooth connections because it has been paired in the past I assume. Once I go into GSX and connect, it changes to "Connected" in the bluetooth connections window.
As far as your slider staying greyed out, you need to left click on the right half of the slider (where it is grey). If you click on the green part and try to drag it to the right, it will pop up the window about changes taking effect after saving, but it won't actually move the slider over.Comment
-
well, that was embarrassing!Originally posted by andygg1986 View Post
it was as simple as clicking on the tight half of the slider.
i think I have everything working now.
just need to fiddle with the settings a bit to make sure everything works smoothly and as it should.
thanks folks!
Comment
-
i bought the TGC license and have GC2. i just got my gaming computer. how do i get access to all the software?Comment
-
After you purchase you need to wait for Protee to send you the downloads. Follow the instructions here to a T. They are up to date. You need to wait for the downloads and licensees.Originally posted by richdmb View PostMy Courses:
World Par 3's by mthunt
Toronto GC (L) mthunt
Burlington G&CC by mthunt
Weston G&CC by mthunt
London Hunt Club L mthunt
Park CC Lidar mthunt
Sunningdale GC Robinson L
Sunningdale GC Thompson L
Muirfield Village (liDAR) First Ever Lidar course
Country Club of Castle Pines (liDAR)
The Sanctuary GC ProTee L
The National GC L mthunt
Mississaugua GC L mthunt
Shaughnessy G&CC L mthunt
Markland Woods CC mthunt
Hidden Lake Old L mthunt
Magna GC L mthunt
Barrie CC L mthunt
mthunt RangeComment
-
need help!
i followed all the directions. TGC is set to on in the interface and GSX. use external data is set to on in the interface. status input and output are connected and i have the green dot in the right upper corner in GSX. bluetooth settings confirms GC2 is "connected" not just paired. i connected to server in TGC then started the game. shots will not launch. when i hit a shot, GC2 displays shot data, but that data is not received in the interface.
any suggestions?
i am eager to start playing!
thanks!Comment
-
I had similar issues after switching from SkyTrak. Even with all the license and machine ID stuff squared away, it still wouldn't work and ProTee remoted into my computer and fixed some security/license issue that was going on behind the scenes. I'd open a ticket with ProTee so they can remote in and get it fixed.Originally posted by richdmb View Post
Comment
-
Same thing is happening to me. I am waiting for protee to get back to me. Their customer support has been awesome so far, but unfortunately its the weekend and its pretty late where they are.Originally posted by richdmb View Post
So, hopefully tomorrow we can get this squared away
Comment
-
Oops forgot tomorrow is Sunday. Hopefully Monday we can get it up and runningComment
-
What version of the protee interface are you running. An older one had a no launch bug for gc2s. The the most recent one should have that fixed.Originally posted by richdmb View PostComment
-
Protee's customer service is outstanding! My issue turned out to be a license issue. They sent me another license key and everything is up and running
Thank you to Protee and to everyone on the forum for all the info they have posted
I think I will post the steps I went through to switch from the Skytrak to the GC2 after i play a round
Comment
Comment